Men's Ocean 1.0
Redefine What’s Possible - Performance Beyond Expectation
The Ocean 1.0 is a thermal lined wetsuit designed for athletes who never back down from a challenge. We incorporated the same zero resistance shoulder movement technology found in our Flōh 1.0 wetsuit and added a ThermaFur thermal lining to create a no-compromises wetsuit. We also integrated an Ocellus pattern on the Ocean 1.0 to make the wetsuit more visible from a greater distance. Don’t let conditions dictate what you can do, when the Ocean 1.0 is paired with the Polar hoodie, gloves, and socks it will keep you warm in water down to 6°C/43°F.
- Super light 44Cell HBF-Limestone WhaleSkin™ neoprene
- 1.5mm UltraFlex shoulders and arms construction
- ThermaFur thermal lining
- Ocellus pattern for increased visibility
- Taped sleeves inside the wrist to keep cold water out
- 5mm 48Cell Airfloat™ Stability Panels
- GlideSkin™ Surface coating
- YKK Stainless Steel bottom-up runner zipper
- Anatomically correct fit ensures peak performance without restrictions
- Rear zip entry for fast and easy entry and exit
- Hand glued with double blind stitched seams
- Made for Cold Temperatures down to 8°C / 46°F (down to 6°C / 43°F when paired with our Polar hoodie, gloves and socks)
ThermaFur is a specially designed thermal lining developed in conjunction with deboer engineers and some of the top athletes in the world. ThermaFur reflects the athletes body heat to keep them warm in cold-water swims. ThermaFur is a polyester based brushed thermal lining with a water repellent quick dry coating. The water repellent quick dry coating allows ThermaFur to be considerably lighter and more effective than traditional thermal wetsuit linings.
The Ocellus pattern increases the visibility of a swimmer. The Ocellus pattern is strategically placed on each shoulder, the point of the elbows, and the back of the calves so that a swimmer can be spotted from a distance by another swimmer, a spectator on shore, or someone on a water vessel. The Monarch colour was chosen because it has been proven to subconsciously trigger an alert signal in anyone who sees it - this will help keep the athlete safer in open water.
WhaleSkin™ - HBF Limestone Rib Neoprene
Limestone neoprene has a high micro-cell structure. These are independent closed cells (like bubbles) within the neoprene that are packed together at extremely high density. Limestone neoprene has a 94% cell penetration - over 30% more than oil-based neoprene leading to greater impermeability, lightness, warmth, durability and stretch with memory allowing more freedom of movement. Our WhaleSkin rib neoprene increases the surface by 18.3%, which in turn increases buoyancy and ultimately increases your speed. In addition, it’s more environmentally friendly.
Warmer than our other materials yet is still incredibly flexible and highly durable. Our exclusive polymer is fingernail tear proof. It has advanced shape memory, 4-way super stretch, and is lined with an ultra-flexible insulating lining also with 4-way stretch.
Made from our HBF-Limestone neoprene (Highly Buoyant, Flexible, and lightweight 48 cell neoprene). We conducted studies to understand how adding buoyancy can affect swim position. Based on these studies, we positioned the panels to create maximum stability, minimize rotation and ensure better balance.
Our unique glide layer coating technology provides exceptionally low water friction and increases hydrodynamics. In addition, it reduces resistance when changing out of your wetsuit, thus, helping to save precious time during your race transition. This coating aids in the reduction of fingernail tears.
We only use YKK stainless steel zippers which close from bottom to top. This makes opening the wetsuit and getting out much easier and therefore, faster in transition.
Care should be taken when donning the wetsuit to avoid damaging the neoprene skin with fingernails. Always use the pads of your fingers to put on a suit. Do not pinch small folds and pull, make sure to grab large folds of the suit when pulling. Small cuts or tears can be repaired with wetsuit glue.
The exterior surface of your wetsuit is manufactured with a hydrophobic outer skin designed to reduce surface friction (drag.) It is designed to withstand the normal wear and tear during a normal swim session. Care should be taken to avoid contact with sharp rocks or any other sharp objects. Small cuts or tears do not affect wetsuit performance.
Fully unzip the wetsuit before removing one section at a time. Avoid contact with sharp fingernails. Salt and chlorine water can damage the neoprene drying it out and affecting its flexibility. To ensure continued flexibility it is important to soak your wetsuit in lukewarm, fresh water for at least 5 minutes after each use, then thoroughly rinse it with fresh water. To dry, place the wetsuit inside out on a wide hanger in a ventilated place, away from direct sunlight. Maintenance is important, therefore it is recommended to wash your wetsuits with a specialized antibacterial soap every few sessions.
Wetsuit material can develop permanent creases if left folded for an extended period of time. Therefore it is best to store your wetsuit laying flat. Alternatively, hang it on a specially designed wetsuit hanger, thick coat hanger, or as wide and thick a hanger as you can find. Consider the weight of a wet or damp wetsuit and avoid deformation around the shoulders. Some like to roll their wetsuits, but do not fold it under any circumstances.
Zippers are designed to be pulled open and closed in a straight line. Avoid pulling at excessive angles. Ask for assistance to zip and unzip as needed.
Chemicals & Solvent
Avoid contact with oil, gasoline, aerosols or any solvents as they degrade rubber and plastic materials. Do not use any type of alcohol, or lubricant.
Free Shipping Worldwide on all orders above $200 USD.
We offer free standard shipping of all orders worldwide above $200 USD. Price includes all taxes and duties.
For all other purchases, shipment rates are calculated at Checkout.
We also offer expedited shipping options, calculated at Checkout.
Can I return my product?
Yes. If you are not 100% satisfied with any deboer product it can be returned within 14 days of delivery provided it is in new condition. For wetsuits new condition means with the tags attached.
Prior to sending your product back to deboer please email our Director of Operations, Brooke Brown - email@example.com. Returns can be sent to:
deboer wetsuits - Sport Import Europe b.v.
Re: Your name and order number
Einsteinstraat 16 B
3316 GG Dordrecht
deboer wetsuits - Method Sourcing
Re: Your name and order number
103 Carolina Court
Archdale, North Carolina, USA, 27263
How do I submit a warranty claim?
All deboer products are guaranteed against manufacturer defects of material and craftsmanship for 1-year from the date of purchase. In the event you need to submit a warranty claim you can email our Director of Operations, Brooke Brown - firstname.lastname@example.org. In your email please include:
- Description of the problem
- Photo of the problem
- Your order number or proof of purchase
Our Warehouses and Couriers
We have warehouses in the USA and the The Netherlands. From our US warehouse we ship via FedEx, UPS, or USPS. From our Netherlands warehouse ship via FedEx, Post NL and DPD.